Off-campus Tasks Lists

Find Source for Fuses. The following models (or similar equivalent) are required:
XEV25-175 3pcs
XEV20-80 5pcs
XEV10-50-B 3pcs
XEV10-20-B 5pcs
XEV10-10-B 5pcs
XEV10-7.5-B 2pcs
XEV10-5-B 2pcs

Board Molex connector + crimp List @Daniel Lin

Off-board Molex Connectors list @Brian Nguyen (Deactivated)
-MX150Ls going through enclosures

Find more docs on the motors @James L
-Inductance specifications

Find mating connector for motor sensor wires @James L
-check motor datasheet
-Shielded cable to use to connect to the motor controller

@Josh Rong Figure out AUX switch implementation on the last car, and make it better on this car.

Talk to interiors to sort out front electronics enclosures and accessibility

Talk to interiors about solar box enclosure and LOCATION @Aashmika Mali

Telemetry @Pei Liang Guo
-CAN wireless dongles?
-LoRa?
-Point to point wireless?
FSGP vs ASC conditions

Lights Heatsinking
-Heat pipes
-mounting to lights boards (screws)

@Former user (Deleted) Lights Mounting

Horn mounting @Darby Smyth
-Waiting for adrian

Figure out Heating of U2 (CAN Transceiver) on charger interface board @Aashmika Mali
-compare schematics with motor controller interface
- see . Issue was dead MCP2515

Wiring diagram for the Elcon - J1772 Adapter @Darby Smyth
-Which wire are we using for this connection?
-match the diagram for the mating ends

Enclosure for MOV Charge Monitoring (read ASC regs)

Mounts for driver ventilation fans
-Noctua NF-F12 iPPC 3000
-Talk to Adrian

Find all nomuras to use (x11)
-maybe remove nomuras from ms12
-Do we need more?

Battery Module Connector Board @Ricky H

GPS Module - RPI @Daniel Lin
-uBlox modules?

Setup Controller board pick and place - VBA script? @Darby Smyth
-Length, width, height of components
-Pick Angle relative to Altium Libraries

Revisit power budget @Josh Rong
-Better documentation!
-We need to figure out if we are as close to the power limit as we thought we were
@Aashmika Mali and @Micah Black to make a list of the power draw in the car
-We added a Sanity Check page to the google doc, and are evaluating alternate solutions for the horn.

Powering the horn from another source? @Liam Hawkins

Lower priority - fan control board (PWM generator)

UV cutoff board @Liam Hawkins - needed for horn and driver fans - talk to micah for more details
-use load switch to activate mosfet for current path from lead acid to component
-load switch will also get voltage level from battery (AND with rear power 12V signal to activate)
-maybe charger feature @ 50mA
-will use 5AH 12V Lead acid pack (probably from amazon) - also test with 1AH one to see if that would work with 5 min horn on time in regs
-regs for supplemental battery enclosures - what is needed?

Find bimetal switch on digikey to control DC-DC fan. Should be Normally Open (NO) and be able to provide at least 0.3A.

Provide a suggestion for wireless tyre pressure monitoring system (TPMS)

Reformat the altium libraries to make sure the following are taken care of
-obsolete components are deleted
-”Manufacturer Part Number 1” is a parameter updated for all components
-No component uses cut tape or Digi-real
-the polarity of components matching pads/pins matching silkscreen is correct
-all parts that (like the standoffs) have correctly implemented keepout layers
-for more info talk to @Micah Black@Josh Rong or @Aashmika Mali (or any other lead)

Go through this page we use before every board sendout and format it better plus update content to be more extensive Checklist for Gerbers