Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 15 Current »

  • Telemetry Pei Liang Guo
    -CAN wireless dongles?
    -LoRa?
    -Point to point wireless?
    FSGP vs ASC conditions
  • Find Source for Fuses. The following models (or similar equivalent) are required:
    XEV25-175 3pcs
    XEV20-80 5pcs
    XEV10-50-B 3pcs
    XEV10-20-B 5pcs
    XEV10-10-B 5pcs
    XEV10-7.5-B 2pcs
    XEV10-5-B 2pcs
  • Lights Heatsinking
    -Heat pipes
    -mounting to lights boards (screws)
  • Former user (Deleted) Lights Mounting
  • Board Molex connector + crimp List Daniel Lin
  • Off-board Molex Connectors list
    -MX150Ls going through enclosures
  • Battery Module Connector Board Ricky H
  • Horn mounting Darby Smyth
    -Waiting for adrian
  • GPS Module - RPI Daniel Lin
    -uBlox modules?
  • Setup Controller board pick and place - VBA script? Darby Smyth
    -Length, width, height of components
    -Pick Angle relative to Altium Libraries
  • Find more docs on the motors James L
    -Inductance specifications
  • Figure out Heating of U2 (CAN Transceiver) on charger interface board Aashmika Mali
    -compare schematics with motor controller interface
    - see Charger Interface Testing . Issue was dead MCP2515
  • Wiring diagram for the Elcon - J1772 Adapter Darby Smyth
    -Which wire are we using for this connection?
    -match the diagram for the mating ends
  • Enclosure for MOV Charge Monitoring (read ASC regs)
  • Mounts for driver ventilation fans
    -Noctua NF-F12 iPPC 3000
    -Talk to Adrian
  • Revisit power budget Josh Rong
    -Better documentation!
    -We need to figure out if we are as close to the power limit as we thought we were
    Aashmika Mali and Micah Black to make a list of the power draw in the car
    -We added a Sanity Check page to the google doc, and are evaluating alternate solutions for the horn.
  • Powering the horn from another source? Liam Hawkins
  • Lower priority - fan control board (PWM generator)
  • Find all nomuras to use (x11)
    -maybe remove nomuras from ms12
  • Find mating connector for motor sensor wires James L
    -check motor datasheet
    -Shielded cable to use to connect to the motor controller
  • UV cutoff board Liam Hawkins - needed for horn and driver fans - talk to micah for more details
    -use load switch to activate mosfet for current path from lead acid to component
    -load switch will also get voltage level from battery (AND with rear power 12V signal to activate)
    -maybe charger feature @ 50mA
    -will use 5AH 12V Lead acid pack (probably from amazon) - also test with 1AH one to see if that would work with 5 min horn on time in regs
    -regs for supplemental battery enclosures - what is needed?
  • Josh Rong Figure out AUX switch implementation on the last car, and make it better on this car.
  • Talk to interiors to sort out front electronics enclosures and accessibility
  • Talk to interiors about solar box enclosure and LOCATION Aashmika Mali
  • Find bimetal switch on digikey to control DC-DC fan. Should be Normally Open (NO) and be able to provide at least 0.3A.
  • Reformat the altium libraries to make sure the following are taken care of
    -obsolete components are deleted
    -”Manufacturer Part Number 1” is a parameter updated for all components
    -No component uses cut tape or Digi-real
    -the polarity of components matching pads/pins matching silkscreen is correct
    -all parts that (like the standoffs) have correctly implemented keepout layers
    -for more info talk to Micah BlackJosh Rong or Aashmika Mali (or any other lead)
  • Go through this page we use before every board sendout and format it better plus update content to be more extensive Checklist for Gerbers
  • Provide a suggestion for wireless tyre pressure monitoring system (TPMS)

  • No labels