- Telemetry Pei Liang Guo
-CAN wireless dongles?
-LoRa?
-Point to point wireless?
FSGP vs ASC conditions - Find Source for Fuses. The following models (or similar equivalent) are required:
XEV25-175 3pcs
XEV20-80 5pcs
XEV10-50-B 3pcs
XEV10-20-B 5pcs
XEV10-10-B 5pcs
XEV10-7.5-B 2pcs
XEV10-5-B 2pcs - Lights Heatsinking
-Heat pipes
-mounting to lights boards (screws) - Former user (Deleted) Lights Mounting
- Board Molex connector + crimp List Daniel Lin
- Off-board Molex Connectors list
-MX150Ls going through enclosures - Battery Module Connector Board Ricky H
- Horn mounting Darby Smyth
-Waiting for adrian - GPS Module - RPI Daniel Lin
-uBlox modules? - Setup Controller board pick and place - VBA script? Darby Smyth
-Length, width, height of components
-Pick Angle relative to Altium Libraries - Find more docs on the motors James L
-Inductance specifications - Figure out Heating of U2 (CAN Transceiver) on charger interface board Aashmika Mali
-compare schematics with motor controller interface
- see Charger Interface Testing . Issue was dead MCP2515 - Wiring diagram for the Elcon - J1772 Adapter Darby Smyth
-Which wire are we using for this connection?
-match the diagram for the mating ends - Enclosure for MOV Charge Monitoring (read ASC regs)
- Mounts for driver ventilation fans
-Noctua NF-F12 iPPC 3000
-Talk to Adrian - Revisit power budget Josh Rong
-Better documentation!
-We need to figure out if we are as close to the power limit as we thought we were
Aashmika Mali and Micah Black to make a list of the power draw in the car
-We added a Sanity Check page to the google doc, and are evaluating alternate solutions for the horn. - Powering the horn from another source? Liam Hawkins
- Lower priority - fan control board (PWM generator)
- Find all nomuras to use (x11)
-maybe remove nomuras from ms12 - Find mating connector for motor sensor wires James L
-check motor datasheet
-Shielded cable to use to connect to the motor controller - UV cutoff board Liam Hawkins - needed for horn and driver fans - talk to micah for more details
-use load switch to activate mosfet for current path from lead acid to component
-load switch will also get voltage level from battery (AND with rear power 12V signal to activate)
-maybe charger feature @ 50mA
-will use 5AH 12V Lead acid pack (probably from amazon) - also test with 1AH one to see if that would work with 5 min horn on time in regs
-regs for supplemental battery enclosures - what is needed? - Josh Rong Figure out AUX switch implementation on the last car, and make it better on this car.
- Talk to interiors to sort out front electronics enclosures and accessibility
- Talk to interiors about solar box enclosure and LOCATION Aashmika Mali
- Find bimetal switch on digikey to control DC-DC fan. Should be Normally Open (NO) and be able to provide at least 0.3A.
- Reformat the altium libraries to make sure the following are taken care of
-obsolete components are deleted
-”Manufacturer Part Number 1” is a parameter updated for all components
-No component uses cut tape or Digi-real
-the polarity of components matching pads/pins matching silkscreen is correct
-all parts that (like the standoffs) have correctly implemented keepout layers
-for more info talk to Micah BlackJosh Rong or Aashmika Mali (or any other lead) - Go through this page we use before every board sendout and format it better plus update content to be more extensive Checklist for Gerbers
- Provide a suggestion for wireless tyre pressure monitoring system (TPMS)
...