Roof Hinge

It is important to note that the top of the roof panel will be flush with the tops/edges of the side panels

Thus, any hinge design considered must be able to lift the roof panel to be cleared/above the side panels. (i.e. the roof panel does not collide/interfere with the side panels during opening and closing)

Four Bar Multi-point Hinge

• Similar to https://www.youtube.com/watch?v=O8gBLLizI3s

  • Or https://www.youtube.com/watch?v=6bMMZq0X29E

    • Assembly process may be more intricate and time consuming

    • Quite a few moving parts, but this is a proven system that has many applications

Pop up Hinge

• Similar to https://www.youtube.com/watch?v=kh252HOZrqc

  • Seems like this will take up more mounting room

  • Concern with the top peg being constantly forced against the top of the slot

    • Would need to ensure the mounting plate (that has the slot) is adhered on properly to provide a sufficient reaction force to the peg’s upward force

  • Motion is also not necessarily smooth and continuous, could be a cause for concern

  • Will have to mount this system flush against the bulkhead

Four Bar Hinge

• This design seems to be utilized in other solar cars as well

  • Four Bar Linkage Roof Hinge.wmv

  • Simpler than the multi-point hinge variant

  • Mounting space is larger than multi-point hinge but less than pop up

    • In MSXIV would have to mount this against the bulkhead panels in order to be feasible

Roof Prop

Two types of roof props will exist: fixed length or variable length

Fixed length:

• Standard rod

  • Essentially a metal or composite rod of a fixed length

Variable Length:

• “Snap Lock”

  • Telescoping rod with a snap on lock, very similar mechanism to those found on telescoping tripod legs

  • 

    • Once the lock is “snapped on”, it induces a compressive force onto the outer tube

      • Which then induces a compressive force onto the inner tube

      • This causes the two tubes to be in contact with one another and therefore frictional force prevents movement of the inner tube

    • Quite user friendly

      • Does not require a lot of input

    • Making the locking mechanism may be quite complicated

      • Need to research applicable manufacturing processes' as well as materials

      • Note: locking mechanisms can be purchased separately and this may allow us to circumnavigate the potential manufacturing issues of this

• Spring Loaded Pin

  • Pin that is attached to an internal spring

    • In the spring’s unstretched position the pin protrudes out

    • User depresses pin and then moves inner rod to desired length

      • Spring will naturally extend back to its unstretched position and pin will protrude out into holes drilled into outer rod, thus locking it in place

  • 

    • Assembly may be quite intricate

      • Making sure the spring and pin are properly assembled within inner rod

    • Restricted to set positions

      • Based on holes drilled into outer rod

    • Not user friendly

      • Sometimes is hard to depress the pin enough while moving the inner rod

• Internal CAM Lock

  • A cam is attached to the inner rod, it is shaped such that when the inner rod is twisted a certain number of degrees, it will push out on a set of plastic/metal halves

  • These plastic/metal halves contact the outer rod

    • Frictional force prevents movement of the outer and inner rods

  • 

  • Assembly of this may be quite complicated

    • Ensuring plastic/metal halves are positioned properly

    • Needing to ensure cam is mounted/positioned properly

    • May be more efficient to purchase this item

  • Quite user friendly

    • Locking/unlocking motion is done by twisting one of the rods

  • NOTE: This may be require additional features to be compatible with some of the mounting methods discussed below

Prop Mounting

The roof prop will need to be mounted to both the roof and chassis of the car in order to properly support the roof

It is also important to note that as the roof prop may need to be removed, the mounting hardware should allow for this as well

Roof Mount:

• Fisheye Hook and Bolt

  • The prop itself will have a fish eye hook while the roof will have an L bracket with a stationary bolt running through

    • The fish eye hook will be placed such that the bolt runs through it as well (see picture below)

    • Image RemovedImage Added

    • NOTE: To be compatible with the twisting motion of the internal cam lock system, the prop would have to be able to ROTATE INDEPENDENTLY of the fish eye hook

      • For the other prop mechanisms discussed above, this mounting method works directly as is

    • Would need a nut on the end to secure the system

      • Unless the bolt is glued/adhered to stay in

      • Above maybe unlikely thus constantly loosening and tightening the nut is not user friendly

    • This system is generally quite simple and straightforward

      • Which should make manufacturing and design easier/faster

• Hook and Pin

  • The prop will have a standard “C-shaped” hook while a pin/dowel that is press-fit between two brackets will be on the roof

    • The hook on the prop will then latch onto this pin/dowel (see below)

    • 

    • NOTE: To be compatible with the twisting motion of the internal cam lock system, the prop would have to be able to ROTATE INDEPENDENTLY of the fish eye hook

      • For the other prop mechanisms discussed above, this mounting method works directly as is

    • System has more components than the “Fisheye Hook and Bolt” method but is still relatively straightforward

      • Press fitting pin/dowel could be a cause for concern

      • Could easily replace this with a shoulder bolt and nut however

    • System is easier to use than the “Fisheye Hook and Bolt” as the prop only needs to be lifted up to unlock, as opposed to sliding out

Chassis Mount:

• Hook to Chassis Tube

  • A hook on the end of the prop would rest directly on the chassis bar in the previously mentioned blue highlighted area

  • Image RemovedImage Added

  • No additional mounting hardware needed, so this theoretically simplifies manufacturing process

  • However, will need to manufacture a hook/integrate a purchased solution such that it will be in this orientation

• Hook and Pin

  • General concept remains the same as how it is applied in the roof mounting scenario

  • Due to the geometry in the mounting area, a pin would potentially be press-fit into a block which would then be adhered onto the bulkhead panel (see below)

  • Image RemovedImage Added

  • This concept requires more mounting hardware

    • Overall more manufacturing work and also adds a bit more weight to the car

  • In addition the concern with how to press-fit the pin/dowel remains

  • May be easier to integrate the end piece (hook) onto a rod than the “Hook to Chassis Tube” method

• Hook and Pin (C-Bracket Variant)

  • Same general concept as above, but instead of a dowel press-fitted within a block, it is placed within a C-bracket

  • Image Added

  • If an adhesive is being used to connect the C-bracket to the bulkhead, then the contact area between the two must be sufficient to allow the bracket to stay in place

    • Would need to calculate this area based on the adhesive and specific material of the C-bracket