Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 5 Current »

how to use

before use: go to licenses and scroll down to PDN analyzer, right-click and click use

  1. open a project’s schematic, then tools >> PDN analyzer
    dc net identification

    • when the analyzer is initially opened, it will attempt to identify all dc power networks from the design’s net data based on common power network nomenclature

      • if not all potential power nets have been identified, deselect appropriate qualifiers filter options or see all nets and select enable all nets for filtering option

  2. use the select check boxes and choose the power nets available to the analyzer. enter suitable voltage levels in the nominal voltage fields and click add selected

  3. specify the power and ground nets

    1. double click ‘power net’ and ‘ground net’ elements in the gui network graphic to open ‘choose net’ dialog. this offers the choice of power nets that have been identified

    2. you can use the dialog’s qualifier/filter options to restrict or expand the listed nets

    3. to extend the power (or ground) net and model the full power path:

      1. right-click on the net you wish to extend and select ‘extend net’

      2. double-click on series to select the connection points between the two power nets (points closest to each)

  4. a source or load element can now be added between the power and ground networks (this is the same process for both load and source)

    1. when selecting the power and ground pins, make sure to select the ones that are directly connected to each rail. all the in-between pins do not matter when specifying the paths


      *you can hover the cursor over any element in the network to see additional information

      1. right-click in the network graphic space and select ‘add source’ / ‘add load’ to open device properties

      2. to add a voltage source, select voltage source from the device type menu

        you can also choose between:

        1. VRM (SMPS) - a switching converter

        2. VRM (linear) - a linear regulator

        3. voltage source - a dc voltage source

      3. the analyzer will attempt to choose the correct net connections - use the ‘Refdes’ menu to specify the component connection points of the source voltage (should be the component closest to the power/ground source depending on which you are setting)

      4. the source parameters specify the attributes of the voltage source simulation

      5. the max source current and pin current are left at the default settings

        1. if the limits are set to specific current values, it will flag a violation of the simulation results exceed those values

      6. you can double click on the pins to remove pins from the network analysis

  5. to view the results

    1. go to the analyzer’s visual tab and set the visual options to display ‘voltage’ for layers

      1. the view of the selected path voltage drop is rendered with a colour gradient that corresponds to the voltage scale at the bottom of the view (red is max level and blue in minimum)

    2. to display the current analysis, select the visual tab’s current density option

      1. the colour levels in the board’s network path relate to the percentage of current density variation (red max calculated current density and blue minimum)
        to view:
        click 2d/3d in view section and go to the .PcbDoc tab of the board

    3. to display and analyze power integrity results in the ground path, deselect the voltage/power network in the net list and select gnd network

    4. to generate a report of the overall results, select report at the bottom and it will create a web link to the results

  6. display and control options

    1. you can clear the analysis results from the editor display which reverts to the graphics rendering to the standard board layout

    2. the overlay option enables the board layout view - useful for confirming where a point of interest in the analysis is located

  7. simulation settings
    the analysis and degree of IR losses also depend on the specification of the board copper conductivity and Via wall thickness

    1. right-click and click settings to view and change these settings

    2. metal conductivity

      1. the base conductivity (or resistivity), temp coefficient and temp can be modified

      2. pure copper – copper is typically assumed to have a conductivity of 5.88e7S/m at 25°C, and a conductivity thermal coefficient of 0.4%/°C

        • ex. this positive temp coefficient means raising the temp. compensation setting in the dialog from 25°C to 125°C will lower the simulation conductivity by 40%, to 3.53e7S/m

      3. pcb copper – (default setting for simulations)

      4. custom – choose this option enter specific conductivity or resistivity values for the simulation

    3. via wall thickness

      1. this is the weight of the via wall metal

      2. can noticeably affect power network dc losses for thin walls. when of sufficient weight/size, it will not impede the dc performance of the design and shows the same current density as the power traces it connects

      3. the simulation assumes the via diameter represents the finished hole size

      4. finished hole diameter + (2 x wall thickness) = drill diameter

        https://www.altium.com/documentation/altium-designer/pdn-analyzer-example-guidev2-ad

  8. working with loads

    1. you can add more loads as necessary

  9. data probe
    the probe tool allows the voltage or current density data at nominated points in the design to be recorded and compared

    1. click probe and click location to select the first location (the highest voltage point)

    2. select difference to select the next location (the lowest voltage point)

  10. locating issues

    1. select high peak values to locate the areas with higher current/voltage values
      this will highlight the location on the board
      step through all of the points using the arrows next to [Locate]

    2. select show arrows to indicate current direction and magnitude

  11. setting limitations

    1. right-click and click settings to set the current limits

    2. networks that contain violations are highlighted with a dashed red outline. double click on the violation entry to view the location of the net

    3. other violations:

      1. the voltage range at a load

      2. max output current from a source

      3. permitted power dissipation in a linear regulator source and its max output current

      4. max output current from a switchmode regulator source

      5. max current through a series element

  12. editing the pcb

    1. you can edit the pcb while the analyzer is active.

    2. click clear in the views section to remove the results and click reanalyze when the edit is complete

  13. voltage contour

    1. the voltage contour feature enables an overlay of dashes displayed as a percentage of voltage drop or as literal voltages

    2. you can use the slider for continuous adjustment or specific points for one point

  • No labels