Skip to end of metadata
Go to start of metadata
You are viewing an old version of this page. View the current version.
Compare with Current
View Page History
« Previous
Version 7
Next »
Design Projects
| Project | Hardware Tasks | Firmware Tasks | Hardware Contact | Firmware Contact | Finish By | Notes |
|---|
| Pre-Charge + Motor Controller Interface | -
HW-111
-
Getting issue details...
STATUS
- Review schematics and complete layout for the PCB
| - Minor changes to IO pin outs to only have one motor contactor and one pre-charge circuit
| Taiping Li |
| Feb 1, 2019 | - Attempt to send out for fab by Jan 18
|
| Steering Interface Board | -
HW-83
-
Getting issue details...
STATUS
|
| Jenny X (Unlicensed) |
| Feb 1, 2019 | - Attempt to send out for fab by Jan 18
|
| Pedal Board | -
HW-82
-
Getting issue details...
STATUS
|
| Aashmika Mali |
| Feb 1, 2019 |
|
| Center Console Board | -
HW-84
-
Getting issue details...
STATUS
|
| Mena Labib |
| Feb 1, 2019 |
|
| BMS Carrier Board | -
HW-87
-
Getting issue details...
STATUS
|
| Taiping Li |
| Feb 28, 2019 |
|
| Charger Interface Board | -
HW-118
-
Getting issue details...
STATUS
|
| Mena Labib |
| Feb 28, 2019 |
|
| Telemetry | - Ensure that the current hardware setup is reliable
- Range testing
| - Implement a Wifi + LTE based system
| Aaron Tan |
| Mar 10, 2019 |
|
Validation & Integration Projects
| Project | Hardware Tasks | Firmware Tasks | Hardware Contact | Firmware Contact | Finish By | Notes |
|---|
| BMS AFE | -
HW-112
-
Getting issue details...
STATUS
- Test and validate new hardware
- Determine accuracy for cell voltage measurements
- Re-harness battery box for Molex Micro-Fit connectors if needed
| - Implement ability to read board and ambient thermistor readings
| | | Feb 1, 2019 | - 1 board has been brought up already and smoke tested
|
| Solar Sense | None |
ELEC-554
-
Getting issue details...
STATUS
- Test and characterize ADC accuracy
| | | Feb 1, 2019 | - Hardware and firmware should be complete, but firmware has not been tested.
|
| BMS Current Sense | -
HW-119
-
Getting issue details...
STATUS
- Characterize the accuracy between - 200 A and + 200 A
| - Assist with reading and saving ADC readings
| |
| Feb 1, 2019 |
|
| Charger Interface |
| - Validate that charger works according to J1772 protocol
- Charge using a level 2 charger
ELEC-497
-
Getting issue details...
STATUS
| | Misha Zharov | Feb 28, 2019 |
|
| State of Charge(SOC) |
|
ELEC-540
-
Getting issue details...
STATUS
- Test the current SOC algorithm based on battery pack data and characterize accuracy
- Write additional test cases if needed
- Integrate into projects/plutus
- Add CAN Output
| N/A | | Feb 1, 2019 |
|
| GPS Driver |
| -
ELEC-71
-
Getting issue details...
STATUS
- Test on the car
| N/A | | Feb 1, 2019 |
|
| MCI and version logging investigation |
| - Check whether version logging is interfering with MCI
ELEC-528
-
Getting issue details...
STATUS
|
| Former user (Deleted) | ? |
|
"Nice to do"
| Project | Description | Person in Charge |
|---|
| Controller Board | - CAN ESD diode has to be fixed
- Look into other potential improvements
| |
| Lights | |
|
Misc things to do
- Determine power budget for MSXIV
- Lights for MSXIV
- Determine preliminary board sizes for battery box
- Determine enclosures needed and approx dimensions
- Motor Controller Cooling
- Find connectors for MSXIV
- Re-harness MSXII's PJB and battery box