Skip to end of metadata
Go to start of metadata

You are viewing an old version of this page. View the current version.

Compare with Current View Page History

« Previous Version 9 Current »

We need to figure out the following:

  • What boards we want to send out, receive, assemble and validate

  • Who has time and resources next term for the above^

  • What resources can liam/josh? take from the bay

Our primary goal for the spring 2020 term is to validate and test every board as well as to have well defined and documented testing procedures to make testing and validation of new boards and rev a breeze in the fall.

Tools/Equipment

  1. Fluke Multimeter (Yellow) and test probes

  2. Agilent Multimeter (Orange) and test probes

    1. Thermocouples

  3. Keysight 34410A 6.5 digit benchtop DMM

  4. Reflow Oven (if possible)

    1. Solder paste, mini fridge, scraper, etc if possible

  5. Heat gun for rework

    1. Kapton Tape could help as well

  6. Soldering iron x 2

    1. Solder, flux as well, copper braid, solder tips, solder braid cleaner

  7. Power Supplies

    1. There is an Agilent one on the battery testing bench (not the high voltage one)

    2. There is a large linear one under the electrical bench

    3. The red and black alligator clips, or at least banana:alligator clips

  8. Microscope if someone is willing to take care of it, and if they let us.

  9. (low priority) Alligator clips

  10. Light Meter - on the shelf near the battery bench

  11. Tweezers

  12. X-acto knife

  13. Benchtop fans for soldering ventilation

Boards/Components

  1. Controller Boards, parts, and stencils, we should have parts or 30.

    1. The rev from JLC PCB with the pick and place panel

  2. The rest of the board boxes above the electrical bench (have all assembled boards)

    1. LEDs from lights box

    2. Definitely get: center console, pedal and lights assembled boards + their boxes

  3. Resistor/capacitor/IC boxes could save us money from having to buy them

  4. Raspberry Pi 3B+, Micro SD Cards, etc.

  5. Wire spools: 22AWG, 18AWG

  6. Molex boxes (microfit + ultrafit + 2pin duraclicks) of connectors + crimps

  7. SWD adapters + programmers (Grab box of firmware stuff)

  8. Boxes with components from previous boards (e.g. box with lights board stuff)

  9. MPPTs x2 (18-33V)

  10. Chen’s aux charger board + stencil

  11. Power supply to ultrafit for board power (might be attached to agilent supply)

  12. Horn

Essentials:

  1. Heat gun for rework

  2. Agilent Power Supply

    1. banana - alligator clips

    2. ultra-fit power connection

  3. Weller Soldering Iron

    1. Solder, flux, copper braid, solder tips, brass sponge, solder paste, kapton tape, extra solder tip

  4. Tweezers, needle nose pliers and Exactoknife

  5. Controller Boards, parts, and stencil, we should have parts for 30

    1. The rev from JLC PCB with the pick and place panel, and the solder paste scraper blade

  6. MPPTs x2 (18-33V)

  7. SWD adapters + programmers (Grab box of firmware stuff)

  8. Raspberry Pi 3B+, Micro SD Cards, etc.

  9. DC-DC Rev 1 box from on top of the electrical shelf (make sure it has the old board, an extra heatsink, push pins and module)

  10. PEAK CAN-USB adapter

  11. Small spool of 22 gauge wire (preferably two colours)

  • No labels