| Info |
|---|
Fall |
...
2023 Onboard - timeline To get everyone started on the battery box team, it would be good to go through the basics of designing a simple battery pack. This exercise will help you understand what you are contributing to this term! You’ll start by reading up on some of the battery pack details and manufacturing methods, and then move to design a simple pack to understand how to put everything together and then provide a recommendation for a battery pack for a car similar to MSXV. This is the exact same process that we go through when starting to design a new pack for the car (or any battery pack for that matter) - so this is all the required knowledge for building battery packs. This project can be completed largely offline in your own time, but there will be discussions during check-ins and feel free to ask questions on Slack at other times! There is quite a bit of reading in this intro and you’ll come across a lot of words you might not know. But fear not! As an engineer, you’ll 100% be in this situation basically always. Although difficult, you’ll probably learn the most in these situations too! So, don’t be discouraged, search up words you don’t know, and if all else fails skip sections and you’ll likely come back to it later with the information needed to understand it!
|
Table of Contents
| Table of Contents | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
...
Onboarding Project
Step 1
Read through these PDFs about designing and building a battery pack. These compile a ton of information - don’t be scared to read them, but be sure to spend the time to understand them. If you have any questions, then message the #mech-battery-box channel on slack and someone will get back to you!
...
https://www.youtube.com/watch?v=8Posj4WMo0o
Battery 101 (Optional but helpful!)
https://www.youtube.com/watch?v=lUZ9l1iAYK8
Start off with reading these: (These are really great!)
Part 1: https://www.electricbike.com/introduction-battery-design-1/
...
| View file | ||
|---|---|---|
|
Part 3 (Optional): https://www.electricbike.com/introduction-to-battery-pack-design-and-building-part-3/
| View file | ||
|---|---|---|
|
...
Here is a Video explaining basic electrical calculations (Hint: these calculations will be used in the exercise):
https://www.youtube.com/watch?v=cX4s-bxn4fs
BRUH! This is so good damn.. bless whoever made this:
https://batteryuniversity.com/articles
Then read these for some more in-depth background for battery packs
| View file | ||
|---|---|---|
|
| View file | ||
|---|---|---|
|
Step 2
We’ll start with a simple pack - here are some of the specs that we want for this project:
...
What do you recommend for the number of cells in series and parallel, and why did you choose those numbers - we’re looking for an answer in the form of XPYS, where X is the number of cells in parallel and Y is the number of cells in series, along with a justification.
Step 3
Draw a diagram of the cells, how they are connected together, and where the main battery terminals are for the battery configuration calculated for Step 2.sketch of the cell plate holders (what will hold the batteries in place to make the connections, see below for an example) you would 3D model for your answer, a simple design will work. This will help you on the working session on the 16th when we design cell plate holders together on SOLIDWORKS 
...
We will be holding a tutorial session on Sept. 16th @ 1:30PM to work through Steps 2 & 3 but we encourage everyone to try on their own first. You will need to answer question 4 on your own so give it your best shot and don’t be scared to reach out for help!
Step 4
Now that you should know how to design a battery pack, we’ll get you to run through the process of choosing a battery configuration for a car, given the following parameters (chosen to loosely represent Midnight Sun XIV):
If you think there’s info missing here, message Micah Black on slack and I’ll first make sure I didn’t make a mistake in the info provided, and then help you out to make sure you’re on the right track!
Car Specs:
Item | Spec | Notes |
|---|---|---|
Race Distance | 3000km | |
Car Average Velocity | 60km/h | Assume average velocity for the entire duration of the race, and that the path is flat. |
Power Consumed travelling at Average Velocity | 1005W | Per Motor |
Peak Motor Power | 5000W | Max power that the motors will draw (per motor) |
Number of Motors | 2 | Motors on each of the 2 rear wheels |
Motor Controller Min, Max Voltage | 50V, 165V | |
Single Cell Min, Max Voltage | 2.5V, 4.2V | At the full charge and full discharge limits |
Nominal Cell Voltage | 3.635V | Average voltage of a cell over the full discharge curve |
Single Cell Capacity | 3450mAh | Assume all cells are perfectly balanced |
Max Discharge Current of Single Cell | 10A | |
Solar Power Input | 800W | Assume the sun is always shining for the entire duration of the race |
What do you recommend for the number of cells in series and parallel, and why did you choose those numbers - we’re looking for an answer in the form of XPYS, where X is the number of cells in parallel and Y is the number of cells in series, along with a justification.
Step 5
Submit your answer to the Battery Leads (Owen Li , Eric Zhao ) Donna Kim , Shem Kim or Nicole Choe through Slack and then we can discuss some more in detail about your answer. We’ll make sure that you understand what you will be contributing to this term!
...
Extra Info
pack design:
https://www.youtube.com/watch?v=2aDyjJ5wj64&ab_channel=LucidMotors
https://www.youtube.com/watch?v=3dD5KmM8ciU&ab_channel=bytesizedengineering
https://www.youtube.com/watch?v=zgHlUwgiARo&ab_channel=ElectricVehiclesSpace
Here is how to arrange the cells to make a battery pack | ELECTRICBIKE.COM,
misc:
https://uwmidsun.atlassian.net/l/cp/uwfmLmmf
reddit I found today: (3) Solar Racing (reddit.com)
data sheet for our cells: PRODUCT SPECIFICATION (dnkpower.com)
asc 24' regulations: ASC2024-Regs-EXTERNAL-RELEASE-B.pdf (americansolarchallenge.org)
| Tip | ||||||||
|---|---|---|---|---|---|---|---|---|
How does the Solar Work? The solar panels on the Midnight Sun Vehicles provide power directly into the High Voltage system, which powers the motors - it's another power source for the car and will lighten the load on the batteries. https://batteryuniversity.com/articles And read “Inside 18650 Cells”: https://www.electricbike.com/inside-18650-cell/ Then read these for some more in-depth background for battery packs:
|