Versions Compared

Version Old Version 52 New Version Current
Changes made by

Jieun Lee

Jieun Lee

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Ownership

Testing/Validation DRI

Contributors

Project DRI

Jieun Lee

None

Daphne Lai (Deactivated)

Task Chart

Task

Status (type “/status”)

Notes

Defined all ASC safety regulations for cover

Status
colourGreen
titlecompleted

Catamaran Cover Testing/Validation Concepting

Research mounting hardware

Status
colourGreen
titleCompleted

Helping Renzo. Looking at click-bonds.

Research fabrics

Status
colourYellow
titleIN Progress

Finding how to place Google Home looking fabric to attach to fibreglass

Research aesthetic design elements

Status
colourGreen
titlecompleted

Research & Planning the seal and marking

Status
colourYellow
titlein Progress

Research 3D Printing

Status
colourYellow
titlein Progress

Placement and Protection for Access Points

Status
colourRed
titlenot started

Assistance Task List

...

Expand

Marking

  • top of each cover must be marked with letters at least 10mm high with

    • “Caution: Chemical Hazard”

    • “High Voltage”

    • type of the battery (ex. Li-ion)

    • any other standard hazard marking specific to the type of battery as well

  • Where to put:

    • one on each cover

      • assuming that it is one on the battery cover and one on rear electronics

Embroidering

  • works almost on any fabric

    • cotton, wool, linen or silk – anything to be honest

    • would really depend on what fabric we choose to do

      • especially on tightly woven fabrics

      • Woven Fabric

      • nylon fabric

        • works for cars typically

        • not cotton (for right now)

Style:

  • Wish if it is embroidered with MS style

    • Roboto font, MS colour (yellow and blue)

      • might change depending on the fabric colour

      • ex. if the fabric colour is darker than what I expect, then the font would be white

How to?

  • could make a sticker and stick it on to the cover

  • or actually mark it to the cover itself

...

easy procedure
Expand

How to make 3D printing less 3D printed looking

  • key point is: how can we smoothen out the surface?

Method

How-to

Pros

Cons

Sources

Sanding

  • will need different seams

  • after sanding, spray filler and spray paint can make the parts to look not like 3D printed

  • able adjust how smooth we want the surface to be

  • can be accurate in a way since we are sanding the parts that we want

  • could make a mistake of sanding to much

  • if it is a large part, time consuming to sand the whole part

https://www.youtube.com/watch?time_continue=258&v=NLoB52nPuao&feature=emb_logo

https://www.youtube.com/watch?v=0vgynnYzo08

Using Acetone

  • pour small amount of acetone into the glass that has paper towel in it

  • put the model inside the glass, and put a small fan in it so that the air moves

  • displace water around so acetone doesn’t leak

  • acetone will melt the 3D model

  • take it out, and dry the 3D model

  • acetone does its job to smooth our the surface

  • takes only about an hour

  • must be printed with ABS (Acrylonitrile Butadiene Styrene)

    • which gives toxic chemical when heated

    • shrinks when it is cold

      • not suitable

  • when doing this, could be dangerous since it is flammable

  • details can be gone

https://www.youtube.com/watch?v=6xFUNFG-UKE

https://www.youtube.com/watch?v=rn4edNztaPU

Using Spray paint / Spray Fast drying polyurethane

(thinking of sticking with this option)

  • spray paint (more than usual) then spray a layer fast drying polyurethane, fan it

  • do this multiple times

  • no need to sand the 3D model

  • the details might be gone

https://www.youtube.com/watch?v=rn4edNztaPU

Shorter Layer height

  • set the layer height as a low number

  • no need to do an extra step of smoothing out the surface

  • time consuming

  • longer the time, easier for the machine to get jam and stuck

https://all3dp.com/2/3d-printer-layer-height-how-much-does-it-matter/

Heating

  • use a heat gun / hot air gun and along the surface of the 3D model

  • fast

(I guess?)

  • able to choose parts to smooth it out

  • can change the shape entirely if it is too hot

https://www.youtube.com/watch?v=SI2AqrxIfkI

https://all3dp.com/2/pla-smoothing-a-beginner-s-guide/

Using brush on coating or 3D Gloop

  • brushing on to the 3D print

  • easy procedure

3D Gloop

  • brushing on to the 3D print

  • depends on types of epoxy

  • limited resource

https://all3dp.com/2/petg-smoothing/ https://www.3dgloop.com/

  • material: PETG

Fabric

Expand

Fabric

  • was thinking of light grey cotton fabric before

  • but now thinking of nylon

    • waiting for other information from other ‘fabric team’ member

    • thinking of sticking the fabric type as well and the similar colour scheme

Ways to attach Fabric

  • 3M Marine Adhesive Sealant 4200 Fast Cure

    • a way to attach fabric on boats

  • contact cement

    • extremely strong chemical, might be to extreme

  • industrial velcro

  • any fabric glue

  • could even make a small gap on the cover and insert the corners of the fabric

    • must figure out where we want to put fabric

Fabric Glue

Padding under the fabric

  • could use a sponge foam role

  • something like foam floor tile

Keeping the fabric clean

  • could use hydrophobic and antimicrobial coating like how Google uses it for google homes

  • the cloth of the car seat can be protected by the fabric protecter – we could use this to the fabric on the cover

...