everything in purple we basically need to see on the dash

kill switch = red button - something's going wrong, stop the car button

p indicator switch = parking indicator switch

• ignore this, doesn't affect dash

there should be a power switch, but not currently on diagram

P LED = indicates we're in park

already purchased D, N, R, (can’t remember if there was another button they already have - Renzo Villanoy do you remember which other one they said ?? if not, will ask again)

fan control: knobs you can turn to certain point and it clicks on

• needs to be accessible on the dash for driver and passenger - will be circular holes on the dash for the knobs to poke through

AUX, Race/Normal

• Race mode will turn off infotainment - does not need to be super accessible

  • switching between race/normal ideally similar to switching between eco and non eco mode

• VEH CAN --> DB9

• Pi USB --> Type A

• USB C charger output --> USB C

Fault LED --> when that LED is on, activates something outside and also on top of car

Fans 1-4 will be mounted on the dash and wiring will run through on the inside

• fans on old car look similar to ones on a real car - direction control and stuff

• only fan control needs to be on rn

all blue squares are enclosures and all red boxes are connectors which need to fit on enclosures

• driver display area, infotainment display area easily accessible

front electronics enclosure should be accessible but does not need to be EASILY accessible - ie could be unscrewed or smth - don't want it to be a big box like old car

there will be slits on the front of the car which will be connected to the fans so there will always be airflow

driver display area has 4 screens --> all connects to the steering wheel

• driver display area should be parallel to driver

pedal board enclosure should be waterproof

can ignore side lights box

kill switch should be flush with car, just needs opening, should not be easily pressed

(front driver, front passenger) side misc. --> adrian has ideas for it already, talk to adrian about it

basically: we're taking care of pedal board enclosure, front electronics enclosure, infotainment display area, driver display area

3 displays: large, drive new haven, camera displays the other three (they are smaller)

Dell 7inch displays

Center display: 15.6 inches https://www.amazon.ca/Anmite-Type-C-Portable-Monitor-Display/dp/B07RDYLTXX/ref=sr_1_20?dchild=1&keywords=15.6+touch+screen+monitor&qid=1614113838&s=pc&sr=1-20

Ports are on the side

Button enclosure

Wiring to the buttons/led

Put them inside with zip ties and on the edges they all go to central

The sticking out portion maybe retract it a bit

Careful with the things sticking out, no protrude (design a cover that is more flush with the enclosure) (more knob)

If you want a logo we can

The dcdc convertor in rear

The auxiliary at the front there will also be a pedal board

Biggest preference if anything has to be taken out it can all be taken out (mounts are designed by electrical team)

Steering wheel

New clockspring

fit into the old steering wheel (is it possible to reuse the old wheel)

reuse the stalk

still need a custom wheel part and attach to the stalk

board with button is in grad cad (steering wheel interface)

horn: is it separate another button through the center (just has to be on the wheel) free placement on the wheel (center is best) which button is up to interiors (5/6/7cm diameter button)

might need something a bit smaller

horn input to steering interface board (separate button)

radio push steering interface board

cruise control (button form)

regen brake toggle

through clockspring into the other board in the wheel

6 cables routing

Side lights and cameras

(separate enclosure) wiring to them

module needs to pop vertically out

Mobius cameras https://www.mobius-actioncam.com/packages/mobius2/

Considered where to place any of the boards (boards will be placed around internal structure of the dash

Parking brake lever is mounted around the driver

Are we expecting to have any interior lighting? (not really)

Ventilation slits in the front of the car for air (still happening not sure where aero has decided to put the cut and routed  to the fans using ventilation tubes)

Must be air intake from outside (re-read regs)

Pedal enclosure will need another enclosure near there

CAN debug will also want another

enclosure  

Where we can put central console

Closure switches have shorter routing

Something else that should probably be mentioned that we didn’t get a chance to talk about is that there needs to be an additional space somewhere behind or adjescent to the driver display to have a raspberry pi with a few peripherals attached to both control driver display and host our telemtry communications - just something to keep in mind