Page Comparison

• everything in purple we basically need to see on the dash

• kill switch = red button - something's going wrong, stop the car button

• p indicator switch = parking indicator switch

  • ignore this, doesn't affect dash

• there should be a power switch, but not currently on diagram

• P LED = indicates we're in park

• already purchased D, N, R, (can’t remember if there was another button they already have - Renzo Villanoy do you remember which other one they said ?? if not, will ask again)

• fan control: knobs you can turn to certain point and it clicks on

  • needs to be accessible on the dash for driver and passenger - will be circular holes on the dash for the knobs to poke through

• AUX, Race/Normal

  • Race mode will turn off infotainment - does not need to be super accessible

    • switching between race/normal ideally similar to switching between eco and non eco mode

  • VEH CAN --> DB9

  • Pi USB --> Type A

  • USB C charger output --> USB C

• Fault LED --> when that LED is on, activates something outside and also on top of car

• Fans 1-4 will be mounted on the dash and wiring will run through on the inside

  • fans on old car look similar to ones on a real car - direction control and stuff

  • only fan control needs to be on rn

• all blue squares are enclosures and all red boxes are connectors which need to fit on enclosures

  • driver display area, infotainment display area easily accessible

• front electronics enclosure should be accessible but does not need to be EASILY accessible - ie could be unscrewed or smth - don't want it to be a big box like old car

• there will be slits on the front of the car which will be connected to the fans so there will always be airflow

• driver display area has 4 screens --> all connects to the steering wheel

  • driver display area should be parallel to driver

• pedal board enclosure should be waterproof

• can ignore side lights box

• kill switch should be flush with car, just needs opening, should not be easily pressed

• (front driver, front passenger) side misc. --> adrian has ideas for it already, talk to adrian about it

• basically: we're taking care of pedal board enclosure, front electronics enclosure, infotainment display area, driver display area

zoom_0.mp4

• Displays: were we considering 1 for each rear camera

• 3 displays: large, drive new haven, camera displays the other three (they are smaller)

• Dell 7inch displays

• Center display: 15.6 inches https://www.amazon.ca/Anmite-Type-C-Portable-Monitor-Display/dp/B07RDYLTXX/ref=sr_1_20?dchild=1&keywords=15.6+touch+screen+monitor&qid=1614113838&s=pc&sr=1-20

• Ports are on the side

• Button enclosure

• Wiring to the buttons/led

• Put them inside with zip ties and on the edges they all go to central

• The sticking out portion maybe retract it a bit

o  

o  

• Careful with the things sticking out, no protrude (design a cover that is more flush with the enclosure) (more knob)

o  

• If you want a logo we can

J
·       

• The dcdc convertor in rear

·       

• The auxiliary at the front there will also be a pedal board

·       

• Biggest preference if anything has to be taken out it can all be taken out (mounts are designed by electrical team)

·       

• Steering wheel

o  

• New clockspring

o  

• fit into the old steering wheel (is it possible to reuse the old wheel)

o  

• reuse the stalk

o  

• still need a custom wheel part and attach to the stalk

o  

• board with button is in grad cad (steering wheel interface)

o  

• horn: is it separate another button through the center (just has to be on the wheel) free placement on the wheel (center is best) which button is up to interiors (5/6/7cm diameter button)

o  

• might need something a bit smaller

o  

• horn input to steering interface board (separate button)

o  

• radio push steering interface board

o  

• cruise control (button form)

o  

• regen brake toggle

o  

• through clockspring into the other board in the wheel

o  

o  

• 6 cables routing

·       

• Side lights and cameras

o  

• (separate enclosure) wiring to them

o  

• module needs to pop vertically out

o  

• Mobius cameras https://www.mobius-actioncam.com/packages/mobius2/

·       

• Considered where to place any of the boards (boards will be placed around internal structure of the dash

·       

• Parking brake lever is mounted around the driver

·       

• Are we expecting to have any interior lighting? (not really)

·       

• Ventilation slits in the front of the car for air (still happening not sure where aero has decided to put the cut and routed  to the fans using ventilation tubes)

·       

• Must be air intake from outside (re-read regs)

·       

• Pedal enclosure will need another enclosure near there

·       

• CAN debug will also want another

enclosure·       

• enclosure  


·       

• Where we can put central console

·       

• Closure switches have shorter routing

• Something else that should probably be mentioned that we didn’t get a chance to talk about is that there needs to be an additional space somewhere behind or adjescent to the driver display to have a raspberry pi with a few peripherals attached to both control driver display and host our telemtry communications - just something to keep in mind