Versions Compared

Version Old Version 46 New Version 47
Changes made by

Jieun Lee

Daphne Lai (Deactivated)

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Ownership

...

Expand

Sticker on Latches

  • 6 latches on the battery cover

    • since the cover can be opened up after all 6 latches are unscrewed, might be possible to have only one sticker/label on one latch (not necessary to have a sticker on all latches)

How to put sticker

  • Image RemovedImage Added

  • put a vinyl sticker on top of the latch so that it covers the screw

    • must be peeled off to gain access to the battery cover

    • putting one sticker on the bottom latch of the battery cover

  • sticker can be written like this:

    • Do Not Open The Cover

  • problem: fabric

    • if we decide to attach the fabric all on the cover, the sticker might not stick well

    • maybe have to glue it with “easy peel off” glue

...

Expand

How to make 3D printing less 3D printed looking

  • key point is: how can we smoothen out the surface?

Method

How-to

Pros

Cons

Sources

Sanding

  • will need different seams

  • after sanding, spray filler and spray paint can make the parts to look not like 3D printed

  • able adjust how smooth we want the surface to be

  • can be accurate in a way since we are sanding the parts that we want

  • could make a mistake of sanding to much

  • if it is a large part, time consuming to sand the whole part

https://www.youtube.com/watch?time_continue=258&v=NLoB52nPuao&feature=emb_logo

https://www.youtube.com/watch?v=0vgynnYzo08

Using Acetone

  • pour small amount of acetone into the glass that has paper towel in it

  • put the model inside the glass, and put a small fan in it so that the air moves

  • displace water around so acetone doesn’t leak

  • acetone will melt the 3D model

  • take it out, and dry the 3D model

  • acetone does its job to smooth our the surface

  • takes only about an hour

  • must be printed with ABS (Acrylonitrile Butadiene Styrene)

    • which gives toxic chemical when heated

    • shrinks when it is cold

      • not suitable

  • when doing this, could be dangerous since it is flammable

  • details can be gone

https://www.youtube.com/watch?v=6xFUNFG-UKE

https://www.youtube.com/watch?v=rn4edNztaPU

Using Spray paint / Spray Fast drying polyurethane (thinking of sticking with this option)

  • spray paint (more than usual) then spray a layer fast drying polyurethane, fan it

  • do this multiple times

  • no need to sand the 3D model

  • the details might be gone

https://www.youtube.com/watch?v=rn4edNztaPU

Shorter Layer height

  • set the layer height as a low number

  • no need to do an extra step of smoothing out the surface

  • time consuming

  • longer the time, easier for the machine to get jam and stuck

Heating

  • use a heat gun / hot air gun and along the surface of the 3D model

  • fast (I guess?)

  • able to choose parts to smooth it out

  • can change the shape entirely if it is too hot

https://www.youtube.com/watch?v=SI2AqrxIfkI

https://all3dp.com/2/pla-smoothing-a-beginner-s-guide/

Using brush on coating

  • brushing on to the 3D print

  • easy procedure

3D Gloop

  • brushing on to the 3D print

  • easy procedure

  • material: PETG

...

Expand

Ways to attach Fabric

  • 3M Marine Adhesive Sealant 4200 Fast Cure

    • a way to attach fabric on boats

  • contact cement

    • extremely strong chemical, might be to extreme

  • industrial velcro

  • any fabric glue

  • could even make a small gap on the cover and insert the corners of the fabric

    • must figure out where we want to put fabric

Fabric Glue

Padding under the fabric

  • could use a sponge foam role

  • something like foam floor tile

Keeping the fabric clean

  • could use hydrophobic and antimicrobial coating like how Google uses it for google homes

  • the cloth of the car seat can be protected by the fabric protecter – we could use this to the fabric on the cover

    Image Added

Access Points

Expand

Access Points are:

  • power supply input

  • AUX battery input

  • USB ports for phone charging

Labeling and Making it professional

  • could label with words and image

ex.

...