Versions Compared

Version Old Version 19 New Version 20
Changes made by

Jieun Lee

Jieun Lee

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

Expand

  • greyish- warm/soft white

  • attach of fabric (grey or it could be coloured)

    • according to Google fabric materials are:

      • Fabric: 33% nylon, 67% polyester

      • Hydrophobic and antimicrobial coating

      • Polycarbonate (hard plastic)

  • could add colour to fibreglass / or colour it afterward

    • if we are sticking with google home aesthetic, just need to make sure that it looks like the white colour they use

    • maybe the first 3 colours? white colour with a tint of grey/beige

    • this colour was used in google store #F8F8F8 in hex

...

    • Image Added
Expand

What to include:

  • top of each cover must be marked with letters at least 10mm high with

    • “Caution: Chemical Hazard”

    • “High Voltage”

    • type of the battery (ex. Li-ion)

    • any other standard hazard marking specific to the type of battery as well

  • indicates contravention of the regulation

    • provisions (like regulations I believe) to seal battery/enclosure - be made by the team

    • to prevent unauthorized actions

Style:

  • MS fonts, colours

  • thinking of small rectangle / square seal

...

Expand

How to make 3D printing less 3D printed looking

  • key point is: how can we smoothen out the surface?

Method

How-to

Pros

Cons

Sources

Sanding

  • will need different seams

  • after sanding, spray filler and spray paint can make the parts to look not like 3D printed

  • able adjust how smooth we want the surface to be

  • can be accurate in a way since we are sanding the parts that we want

  • could make a mistake of sanding to much

  • if it is a large part, time consuming to sand the whole part

https://www.youtube.com/watch?time_continue=258&v=NLoB52nPuao&feature=emb_logo

https://www.youtube.com/watch?v=0vgynnYzo08

Using Acetone

  • pour small amount of acetone into the glass that has paper towel in it

  • put the model inside the glass, and put a small fan in it so that the air moves

  • displace water around so acetone doesn’t leak

  • acetone will melt the 3D model

  • take it out, and dry the 3D model

  • acetone does its job to smooth our the surface

  • takes only about an hour

  • must be printed with ABS (Acrylonitrile Butadiene Styrene)

    • which gives toxic chemical when heated

    • shrinks when it is cold

      • not suitable

  • when doing this, could be dangerous since it is flammable

  • details can be gone

https://www.youtube.com/watch?v=6xFUNFG-UKE

https://www.youtube.com/watch?v=rn4edNztaPU

Using Spray paint / Spray Fast drying polyurethane

  • spray paint (more than usual) then spray a layer fast drying polyurethane, fan it

  • do this multiple times

  • no need to sand the 3D model

  • the details might be gone

https://www.youtube.com/watch?v=rn4edNztaPU

Shorter Layer height

  • set the layer height as a low number

  • no need to do an extra step of smoothing out the surface

  • time consuming

  • longer the time, easier for the machine to get jam and stuck

Ways to Attach Fabric

Expand

  • 3M Marine Adhesive Sealant 4200 Fast Cure

    • a way to attach fabric on boats

  • contact cement

    • extremely strong chemical, might be to extreme

  • industrial velcro

  • any fabric glue

  • could even make a small gap on the cover and insert the corners of the fabric